What's the salary range for a good CNC Admin? *DELETED* *DELETED*

StewartSchatz

StewartSchatz

Well Known Member
What\'s the salary range for a good CNC Admin? *DELETED* *DELETED*

Sorry everyone. I need to re-think this post. There are way too many variables to consider. I'll try to come up with a more precise pole and post it.

Until then, please disregard this post.

Thanks.
 
Re: What\'s the salary range for a good CNC Admin?

In what country?
 
Re: What\'s the salary range for a good CNC Admin?

Hi Sebastian & Stewart,

[ QUOTE ]
In what country?

[/ QUOTE ]

Good question.

E.g. in Hungary, salaries are fairly different, than in USA, West Europe or in Australia, further the taxes are also (higher).

I suppose, the sceanario is somthing similar in Middle/South/East Europe region.

IMHO, this poll can produce realistic results only by regions.

I am really curious to see the results of the poll, but I do not want to vote, because I do not want to distort the results - further there isn't any salary category for me to vote
frown.gif


Stewart,
Can you somehow modify the poll, making possible for me to see the results?
E.g.:
- adding a new panel with regions
- adding new selecteion, e.g. voted just to see the results
- etc.

Regards,

Zoltán
 
Re: What\'s the salary range for a good CNC Admin?

I would suggest that if you are seriously trying to gauge your salary against the industry, there are better methods than trying to put a poll together.

I'd suggest looking at dice.com - somewhere on their website there was a salary comparison matrix based on their readers. That is certainly a better way to gauge salaries.
 
Re: What\'s the salary range for a good CNC Admin?

Ok...this may be a little personal, but I have been working for about 6
years as a CNC Admin. I have been receiving calls about other CNC
opportunities. So, I'm curious about the average salary for CNC Admins:
This post contains the poll as shown below. To vote, please visit the
JDEList Forums ( http://www.jdelist.com/ubb ).



Does your organization have a position with the title
You may choose only one

Yes
No


CNC Admin salary range: Large Metropolitan Area
You may choose only one
$120,000+
$100,000 - 120,000
$80,000 - 100,000
$60,000 - 80,000
$40,000 - 60,000


CNC Admin salary range: Medium Metropolitan Area
You may choose only one
$120,000+
$100,000 - 120,000
$80,000 - 100,000
$60,000 - 80,000
$40,000 - 60,000


CNC Admin salary range: Rural Area
You may choose only one
$120,000+
$100,000 - 120,000
$80,000 - 100,000
$60,000 - 80,000
$40,000 - 60,000


Votes accepted from 4/4/2007 10:32 AM to 4/30/2007 11:59 PM
You must vote before you can view the results of this poll

JDE EnterpriseOne 8.11 SP1 8.95_P1 iSeries Ent. Server V5R3 Win2003
WebSphere 5.0.2.11 / IBM HTTP Server 2.0 e1tips.blogspot.com (
http://e1tips.blogspot.com/ )

The entire JDELIST thread (
'http://www.jdelist.com/ubb/showflat.php?Cat=&Board="OW"&Number="119034"'
) is available for viewing.

Looking for a job? Check out the Job Opportunites forum (
http://www.jdelist.com/ubb/postlist.php?Cat=&Board=Opps )

This is the JDELIST EnterpriseOne Mailing List.
JDELIST is not affiliated with JDEdwards®.
To unsubscribe from this list via email, Click here ( mailto:
[email protected]?Subject=Unsubscribe&Body=Sirs,

Please
remove this address from the JDELIST EnterpriseOne Mailing
List.

Thank You. ).


NOTICE: Please note that this e-Mail, and the contents thereof, is subject to the standard Smiths e-Mail disclaimer which may be found at:
http://www.smiths.co.za/disclaimer.htm

If you cannot access the disclaimer through the URL attached and you wish to receive a copy thereof please send an e-Mail to [email protected]
 
Back
Top