Table Conversion

gng_ca

Member
Hi,

I created a Table Conversion UBE and added a
Processing Option afterwards. The PO value does seem
to be retrieved when running the program. I debugged
the TC, the Processing Option field exists but the
value is 'NULL', disregard the value I entered in.

Any help is appreciated.

Gordon



__________________________________________________
Do You Yahoo!?
From homework help to love advice, Yahoo! Experts has your answer.
http://experts.yahoo.com/
 

rob_malott

Member
Make sure that you have choosen either option 1 or 2 for Prompting on the
Version Detail form.

Rob Malott
OneWorld Developer
J.D. Edwards Product Certified Professional
Brandywine Computer Group
e-mail [email protected]
Phone (513)459-0009
Cell (513)236-5123
 

got_to_love_jde

Reputable Poster
not sure if this will help but i always create report variables and the move the PO values into those variables before i start to work with the values.
good luck.
dave
 

Zoltan_Gyimesi

Legendary Poster
Hi Gordon,

If you make changes on PO templates after you attached and used it in an APPL or UBE sometimes can cause problems.
In this case you may have to revise all ER lines where they are used by double-clicking the lines and revising/correcting them and save the line, the Event and the APPL/UBE.

A very good habit to use variables in the ERs instead of PO valuse as Dave (got_to_love_jde) had written, because in that case you have to revise only that line where you move the PO values into the variables.

Making changes on PO templates can make necessary to re-create versions too (NOT to Copy but Add).

Hope, could help.

Zoltán
 

achimirel

Member
Good point Zoltan.
Gordon, you may want to check out the useful "One World Developers Tips and
Traps" Contributed by Tony St.Pierre in the JDEList's Downloads section.
Regards, Adrian


>From: Zoltan_Gyimesi <[email protected]>
>Reply-To: [email protected]
>To: [email protected]
>Subject: Re: Table Conversion ~~278:327
>Date: Thu, 2 Nov 2000 09:57:21 -0800 (PST)
>
>Hi Gordon,
>
>If you make changes on PO templates after you attached and used it in an
>APPL or UBE sometimes can cause problems.
>In this case you may have to revise all ER lines where they are used by
>double-clicking the lines and revising/correcting them and save the line,
>the Event and the APPL/UBE.
>
>A very good habit to use variables in the ERs instead of PO valuse as Dave
>(got_to_love_jde) had written, because in that case you have to revise only
>that line where you move the PO values into the variables.
>
>Making changes on PO templates can make necessary to re-create versions too
>(NOT to Copy but Add).
>
>Hope, could help.
>
>Zoltán
>
>
>--------------------------
>Visit the forum to view this thread at:
>http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=&Board=OWDEV&Number=327
>*************************************************************
>This is the JDEList One World Developers Mailing List.
>Archives and information on how to SUBSCRIBE, and
>UNSUBSCRIBE can be found at http://www.JDELIST.com
>*************************************************************
>

_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.

Share information about yourself, create your own public profile at
http://profiles.msn.com.
 

Zoltan_Gyimesi

Legendary Poster
Adrian,
Few weeks ago I tried it to download without success, now I tried again but it was unsuccessfull too.
I put this issue onto the General Forum too.
Zoltán
 
Top