DRezanka
Reputable Poster
RE: Quick Start ??291:333
I've had this option do strange things to me when re-editing a program.
Sometimes it works fine; sometimes not. After spending many hours trying to
figure out what the problem was, I wrote it off to the JDE documentation that
says this option is for creating the initial application only and that any
changes need to be entered at SVR from there.
Hope someone else has a better answer.
Doug Rezanka - Programmer/Analyst
Eaton - Actuators and Sensors Division
[email protected]
---------- Original Text ----------
From: C=US/A=INTERNET/DDA=ID/jdeworld(a)jdelist.com, on 11/2/00 1:41 PM:
Actually it did some weird stuff - I have lost of my heading on my video. I
did use the chgdspf command to check if restore display was set to *yes.
Any clues?
Rae Lynne Smith
ComDoc, Inc.
330-899-8026
sdollard
<[email protected]> To:
[email protected]
Sent by:
cc:
owner-jdeworldml@j Subject: RE: Quick Start
~~291:325
delist.com
11/02/00 12:43
PM
Please respond
to
jdeworld
Are you sure it didn't rebuild the source. I should have!!
Steve
--------------------------
To view this thread, visit the JDEList forum at:
http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=0&Board=W&Number=325
*************************************************************
This is the JDEList World Mailing List.
Archives and information on how to SUBSCRIBE, and
UNSUBSCRIBE can be found at http://www.JDELIST.com
*************************************************************
--------------------------
To view this thread, visit the JDEList forum at:
http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=0&Board=W&Number=333
*************************************************************
This is the JDEList World Mailing List.
Archives and information on how to SUBSCRIBE, and
UNSUBSCRIBE can be found at http://www.JDELIST.com
*************************************************************
Doug Rezanka
Applications Developer
Eaton - Actuator & Sensors Division
I've had this option do strange things to me when re-editing a program.
Sometimes it works fine; sometimes not. After spending many hours trying to
figure out what the problem was, I wrote it off to the JDE documentation that
says this option is for creating the initial application only and that any
changes need to be entered at SVR from there.
Hope someone else has a better answer.
Doug Rezanka - Programmer/Analyst
Eaton - Actuators and Sensors Division
[email protected]
---------- Original Text ----------
From: C=US/A=INTERNET/DDA=ID/jdeworld(a)jdelist.com, on 11/2/00 1:41 PM:
Actually it did some weird stuff - I have lost of my heading on my video. I
did use the chgdspf command to check if restore display was set to *yes.
Any clues?
Rae Lynne Smith
ComDoc, Inc.
330-899-8026
sdollard
<[email protected]> To:
[email protected]
Sent by:
cc:
owner-jdeworldml@j Subject: RE: Quick Start
~~291:325
delist.com
11/02/00 12:43
PM
Please respond
to
jdeworld
Are you sure it didn't rebuild the source. I should have!!
Steve
--------------------------
To view this thread, visit the JDEList forum at:
http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=0&Board=W&Number=325
*************************************************************
This is the JDEList World Mailing List.
Archives and information on how to SUBSCRIBE, and
UNSUBSCRIBE can be found at http://www.JDELIST.com
*************************************************************
--------------------------
To view this thread, visit the JDEList forum at:
http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=0&Board=W&Number=333
*************************************************************
This is the JDEList World Mailing List.
Archives and information on how to SUBSCRIBE, and
UNSUBSCRIBE can be found at http://www.JDELIST.com
*************************************************************
Doug Rezanka
Applications Developer
Eaton - Actuator & Sensors Division
