Batch Versions on WTS

[Gerd_Renz]

Dear List,

I am using WTS and most programms behave normally as we could see so far.
Only when I go into Batch Versions or IV I am getting a grey screen for
about 5 minutes. Once started up both programms work fine. In other words,
BV as well as IV take over 5 minutes to open up.

First thing we checked was OCM mappings for BSFNs. I tested in PY7333 and
WPY7333 with out-of-the-box OCM mappings. PY7333 has no BSFN mapped
anywhere, so they all run locally. WPY7333 has a DEFAULT mapping for BSFNs
to the ES and some BSFNs are mapped locally (like I said, as shipped by
JDE). In both environments it takes over 5 minutes for BV or IV to open up
on the screen.
There is no difference sitting at the server's console. All our fat clients
are ok.
We have 3 WTSs installed (by Microsoft technical personnel), all three
servers behave the same.
I am using pristine specs. I build full dddict, ddtext and glbltbl TAM specs
and applied them, no difference.

I know I should use Citrix, but then, it should work without it (please do
not discuss this point).

Any ideas?

Thanks, Gerd
Xe, HP9000, Oracle 8.1.6, WTS (on W2K)

 

[SSAJAROFF]

Gerd :

Check that all your NT users on the Terminal Server have mapped the
\\Deployment\B733 to a letter drive, such as Q: or F:
I've experienced the same problem...

Yours,

Sebastian Sajaroff
CNC Specialist
Grupo ASSA - Application Software SA
(54)-11-4510-7200 Ext 7166
MCSE,MCDBA,MCP+I,Citrix Admin

-----Mensaje original-----
De: Gerd_Renz [mailto:[email protected]]
Enviado el: Jueves, 18 de Enero de 2001 03:16 p.m.
Para: [email protected]
Asunto: Batch Versions on WTS ~~0:4240


Dear List,

I am using WTS and most programms behave normally as we could see so far.
Only when I go into Batch Versions or IV I am getting a grey screen for
about 5 minutes. Once started up both programms work fine. In other words,
BV as well as IV take over 5 minutes to open up.

First thing we checked was OCM mappings for BSFNs. I tested in PY7333 and
WPY7333 with out-of-the-box OCM mappings. PY7333 has no BSFN mapped
anywhere, so they all run locally. WPY7333 has a DEFAULT mapping for BSFNs
to the ES and some BSFNs are mapped locally (like I said, as shipped by
JDE). In both environments it takes over 5 minutes for BV or IV to open up
on the screen.
There is no difference sitting at the server's console. All our fat clients
are ok.
We have 3 WTSs installed (by Microsoft technical personnel), all three
servers behave the same.
I am using pristine specs. I build full dddict, ddtext and glbltbl TAM specs
and applied them, no difference.

I know I should use Citrix, but then, it should work without it (please do
not discuss this point).

Any ideas?

Thanks, Gerd
Xe, HP9000, Oracle 8.1.6, WTS (on W2K)




--------------------------
To view this thread, visit the JDEList forum at:
http://198.144.193.139/cgi-bin/wwwthreads/showflat.pl?Cat=0&Board=OW&Number=
4240
*************************************************************
This is the JDEList One World / XE Mailing List.
Archives and information on how to SUBSCRIBE, and
UNSUBSCRIBE can be found at http://www.JDELIST.com
*************************************************************